This thirteenth brochure showcases the Industrial Flanges portfolio manufactured and supplied by Jayshree Industrial Corporation. These critical piping components are engineered to connect pipes, valves, pumps, and other equipment to form a high-integrity, easily accessible pressure piping network. ------------------------------ ## 🔎 Flange Type Matrix & Visual Range The brochure highlights 8 primary visual configurations alongside specialized industrial designs engineered to accommodate varied pressure, structural, and sealing requirements: * Weldneck: Features a long tapered hub that is welded to the pipe end, providing maximum reinforcement for high-pressure systems. * Slipon: Slides directly over the pipe and is welded both inside and outside for easy alignment and low-cost installation. * Blind: A solid metal disk with no center bore used to permanently seal or block off the end of a piping run or pressure vessel opening. * Socket Weld: Designed for smaller-diameter, high-pressure lines where the pipe inserts into a recessed socket before being fillet welded. * Lap Joint: Used in conjunction with a stub-end fitting, allowing the outer flange ring to freely rotate for easy bolt-hole alignment. * Spectacles (Spectacle Blind): A safety device consisting of a solid steel circle and a hollow ring used to easily isolate or open a pipeline section. * Ring Joint (RTJ): Features a machined groove on the face to accommodate a solid metal ring gasket, optimized for hyper-pressure and high-temperature environments. * Orifice Flange: Designed with radial tapped holes in the ring to hold metering instruments for measuring fluid or gas flow rates. * Specialty Profiles: Includes Long Weldneck, Deck Flange, and other custom configurations. ------------------------------ ## ⚙️ Technical Specifications & Pressure Ratings These heavy-duty flanges adhere to rigid international dimensional, manufacturing, and pressure standards: | Engineering Parameter | Profile Selection Matrix | |---|---| | Pressure Classes | 150#, 300#, 400#, 600#, 900#, 1500#, and 2500# | | Standard Sizing Span | 1/4' NB to 24' NB (Custom sizes above 24' fully supported per customer request) | ## Material Grades Portfolio: * Carbon Steel (CS): ASTM A105, A694 F42/46/52/56/60/65/70, low-temperature A350 LF2, and C22.8. * Alloy Steel: High-temp infrastructure grades including ASTM F1, F5, F11, F22, and F91. * Stainless Steel (SS): Standard and low-carbon variants including ASTM A182 F304/304L/304H, 316/316L, 317/317L, 321, 310, 347, and 904L. * Specialty Exotic Materials: High-performance alloys like Monel, Nickel, Inconel, Hastelloy, Copper, Brass, Bronze, Titanium, Tantalum, Bismuth, Aluminium, High Speed Steel, Zinc, and Lead. ------------------------------ ## 📌 Supplier Contact & Integration Hub For pricing matrices or layout compliance inquiries, you can reach their primary technical sales team directly: * Direct Mobile Liaison: +91 99675 45457 (Bharat Rathod) * Corporate Mailbox: materials.jayshree@gmail.com * Warehouse & Facility: Shop No. A133, Suvan Business Park, Keval Kanta Road, Rakhial, Ahmedabad – 380023, Gujarat, India * Web Domain: Jayshree Industrial Corporation Website ------------------------------ If you are organizing your pipeline bill of materials or looking to finalize a procurement request, let me know if you would like me to: * Draft a formal RFQ email template addressed to Bharat Rathod for a specific size, class (e.g., 150# or 300#), and grade of these flanges * Create a comprehensive Master RFQ combining these Flanges with any previously reviewed items (such as butt weld fittings, flexible hoses, or valves) * Explain when your pipeline dynamics would require a Weldneck flange versus a Slipon flange based on operating pressures
This is your website preview.
Currently it only shows your basic business info. Start adding relevant business details such as description, images and products or services to gain your customers attention by using Boost 360 android app / iOS App / web portal.
Flanges Manufacturers In Gujarat
2026-09-28T18:32:57
This thirteenth brochure showcases the Industrial Flanges portfolio manufactured and supplied by Jayshree Industrial Corporation. These critical piping components are engineered to connect pipes, valves, pumps, and other equipment to form a high-integrity, easily accessible pressure piping network. ------------------------------ ## 🔎 Flange Type Matrix & Visual Range The brochure highlights 8 primary visual configurations alongside specialized industrial designs engineered to accommodate varied pressure, structural, and sealing requirements: * Weldneck: Features a long tapered hub that is welded to the pipe end, providing maximum reinforcement for high-pressure systems. * Slipon: Slides directly over the pipe and is welded both inside and outside for easy alignment and low-cost installation. * Blind: A solid metal disk with no center bore used to permanently seal or block off the end of a piping run or pressure vessel opening. * Socket Weld: Designed for smaller-diameter, high-pressure lines where the pipe inserts into a recessed socket before being fillet welded. * Lap Joint: Used in conjunction with a stub-end fitting, allowing the outer flange ring to freely rotate for easy bolt-hole alignment. * Spectacles (Spectacle Blind): A safety device consisting of a solid steel circle and a hollow ring used to easily isolate or open a pipeline section. * Ring Joint (RTJ): Features a machined groove on the face to accommodate a solid metal ring gasket, optimized for hyper-pressure and high-temperature environments. * Orifice Flange: Designed with radial tapped holes in the ring to hold metering instruments for measuring fluid or gas flow rates. * Specialty Profiles: Includes Long Weldneck, Deck Flange, and other custom configurations. ------------------------------ ## ⚙️ Technical Specifications & Pressure Ratings These heavy-duty flanges adhere to rigid international dimensional, manufacturing, and pressure standards: | Engineering Parameter | Profile Selection Matrix | |---|---| | Pressure Classes | 150#, 300#, 400#, 600#, 900#, 1500#, and 2500# | | Standard Sizing Span | 1/4' NB to 24' NB (Custom sizes above 24' fully supported per customer request) | ## Material Grades Portfolio: * Carbon Steel (CS): ASTM A105, A694 F42/46/52/56/60/65/70, low-temperature A350 LF2, and C22.8. * Alloy Steel: High-temp infrastructure grades including ASTM F1, F5, F11, F22, and F91. * Stainless Steel (SS): Standard and low-carbon variants including ASTM A182 F304/304L/304H, 316/316L, 317/317L, 321, 310, 347, and 904L. * Specialty Exotic Materials: High-performance alloys like Monel, Nickel, Inconel, Hastelloy, Copper, Brass, Bronze, Titanium, Tantalum, Bismuth, Aluminium, High Speed Steel, Zinc, and Lead. ------------------------------ ## 📌 Supplier Contact & Integration Hub For pricing matrices or layout compliance inquiries, you can reach their primary technical sales team directly: * Direct Mobile Liaison: +91 99675 45457 (Bharat Rathod) * Corporate Mailbox: materials.jayshree@gmail.com * Warehouse & Facility: Shop No. A133, Suvan Business Park, Keval Kanta Road, Rakhial, Ahmedabad – 380023, Gujarat, India * Web Domain: Jayshree Industrial Corporation Website ------------------------------ If you are organizing your pipeline bill of materials or looking to finalize a procurement request, let me know if you would like me to: * Draft a formal RFQ email template addressed to Bharat Rathod for a specific size, class (e.g., 150# or 300#), and grade of these flanges * Create a comprehensive Master RFQ combining these Flanges with any previously reviewed items (such as butt weld fittings, flexible hoses, or valves) * Explain when your pipeline dynamics would require a Weldneck flange versus a Slipon flange based on operating pressures
2026-09-28T18:32:57
Submit Your Enquiry